How to make large tufting frame

Do you want to make a large tufting frame but don’t know where to start? If so, then this article is perfect for you! In this how-to guide, we will provide detailed instructions on how to make a large tufting frame from the ground up. From gathering the correct materials and tools to assembling it with ease, this article has got you covered.

Tufting Frames

Making a large tufting frame can seem daunting at first, but with the right tools and materials, it can be an enjoyable DIY project. To start, you’ll need to gather four pieces of wood that are at least 2 inches thick and 6 feet long for the sides of your frame. Next, measure out two shorter pieces of wood that will serve as the top and bottom braces of your frame.

Once you have all your wood cut to size, pre-drill holes where you will be attaching the braces to each side piece. Then attach everything together using screws or bolts. After assembling the basic frame structure, add a layer of foam padding on top and wrap it securely in batting material.

Finally comes the most fun part: adding tufting buttons! Use a needle and thread to pull through from one side to another while pulling tight so that it forms a tufted button look on both sides of your fabric covering. Repeat this process until all desired areas are covered with buttons – then enjoy your beautiful new tufting frame!

Step 1: Gather Materials

The first step in making a large tufting frame is to gather all the necessary materials. This includes a wooden board that’s about two feet wide and four feet long, eye screws, twine or string, a staple gun, batting or foam padding material, and fabric of your choice. The size of the board can vary based on personal preference and what you plan to use the frame for.

Once you have gathered all the materials, it’s important to measure and mark where the eye screws will be placed on the wooden board. Eye screws should be evenly spaced along each side of the board at intervals of about 3-4 inches apart. Drill pilot holes where you’ve made your marks so that the eye screws can easily screw into place.

After screwing in all of your eye screws onto your wooden board, run strings through them and knot them securely on both ends. Then stretch out batting or foam padding material over strings until it covers enough area for tufting work. Finally, cover with fabric which should be big enough to wrap around edges of wood then staple gun it down tightly ensuring there are no wrinkles.

Step 2: Cut and Assemble Frame

To make a large tufting frame, the second step is to cut and assemble the frame. You will need four pieces of wood measuring 2×2 inches and two pieces measuring 1×4 inches. Cut the 2x2s into two equal lengths to form the sides of your frame, then cut the remaining 1x4s into two shorter pieces for the top and bottom.

Next, use screws to join one side piece with one top or bottom piece. Repeat this process for all four corners until you have a complete frame. Make sure that each corner is square so that your finished product looks neat and professional.

Finally, sand all rough edges to avoid any splinters or cuts during use. Your tufting frame should now be ready for the next step in creating beautiful tufted designs!

Step 3: Attach Dacron

Once you have your tufting frame assembled, the next step is to attach dacron. Dacron is a synthetic material used for padding and insulation. It will give your tufted cushion a fuller look and make it more comfortable to sit on.

To attach dacron, start by measuring out enough material to cover the entire frame with an extra inch or two on each side. Then, lay the dacron over the frame and use a staple gun to secure it in place. Make sure to pull it tight as you staple so that there are no wrinkles or sagging areas.

Once the dacron is attached, trim off any excess material around the edges of the frame using scissors or a utility knife. Your tufting project is now ready for its final layer of fabric!

Step 4: Secure Strings

For the tufting frame, securing strings is an important step. The string must be secured to prevent it from slipping or unraveling during use. To do this, start by tying a knot at the end of the string and then looping it around one of the pegs on the frame. From there, wrap the string around each peg in a sequential pattern until you reach the end.

Once you’ve wrapped all of the pegs, tie another knot to secure the string in place. This knot should be snug but not too tight, as you’ll need to adjust tension later on when tufting your project. Repeat this process for each row of pegs until your tufting frame is fully strung.

When using your tufting frame for a project, make sure to regularly check and adjust tension as needed by loosening or tightening knots at either end of your strings. With properly secured strings and consistent tension adjustments throughout your project’s creation, you can create beautiful and professional-looking tufted pieces that are sure to impress!

Step 5: Create Tufts

To create tufts, you need a large tufting frame. A tufting frame is essentially a wooden board with evenly spaced holes drilled into it that allow you to thread yarn through and create loops or “tufts” on the surface of your fabric. To make a large tufting frame, you’ll need to start with a piece of plywood cut to the desired size.

Next, mark out the spacing for your holes in even rows across the board. Use an electric drill with a small bit to drill each hole all the way through the board. Make sure that each hole is clean and free from splinters or rough edges that could snag your yarn.

Once all of your holes are drilled, sand down any rough spots on both sides of the board until it’s smooth and even. Finally, attach legs or stands to prop up your frame at a comfortable working height for easy tufting. Now you’re ready to start creating beautiful tufts on fabric!


In conclusion, creating a large tufting frame is an achievable task with the right tools and materials. It’s important to measure and cut the wood accurately to ensure stability and durability. The use of clamps will assist in keeping the frame together while drilling and screwing in the pieces.

When selecting your fabric or material, it’s crucial to choose one that will withstand frequent use as well as being easy to clean should any spills occur during the tufting process. Once you have completed constructing your frame, it’s time to get creative with your tufting design! Don’t be afraid to experiment with different patterns and textures for a truly unique end result.

Overall, making a large tufting frame requires patience, precision, and creativity. By following these simple steps and using high-quality materials, you can create a stunning piece of furniture that you’ll be proud to show off in your home or workspace for years to come.

Leave a Reply

Your email address will not be published. Required fields are marked *